How to Check and Study Sensor CMP Santa Fe

 

How to Check and Study CMP Sensor of Santa Fe

2003  G 2.0 DOHC  Engine  Unleaded GEN  P0340 Camshaft Position Sensor Circuit Malfunction

Study Terminal and Connector Inspection

1.Many malfunctions Study in the electrical system are caused by poor harness(s) and terminals.Study Faults can also be caused by interference from other electrical systems, and mechanical or chemical damage.

2.Study Check the following conditions:

(1)Study Check for damaged harness and terminals: contact resistance, oxidation, bent or broken terminals.

(2)Study Check for poor connection between ECM and component: backed out terminal, improper mating, broken locks or poor terminal to wire connection

Study Use a suitable male pin to ensure that contact in sockets is good. The pin should remain in position when pulled gently.

3.Study Has a problem been found?

YES

1)Study Repair as necessary and go to "Verification of Vehicle Repair" procedure

NO

1)Go to "Power Circuit Inspection" procedure Study .

Power Supply Circuit Inspection

Check Power to CMPS

1.IG KEY : OFF , Engine : OFF of this Study

2.Disconnect CMPS connectorC01 of this Study.

3.IG KEY : ON , Engine : OFF

4.This Study Measure voltage between terminal 3 of the CMPS harness connectorC01 and chassis ground.

A.Study [Specification] Approx.B+

5.Study Is the voltage near the specified value?

YES

1)Go to "Ground Circuit Inspection" procedure Study.

NO

1)Study to Repair open or short to ground in harness, Go to "Verification of Vehicle Repair" procedure Study.

Ground Circuit inspection

Check for Open in Harness

1.IG KEY : OFF , Engine : OFF

2.Disconnect CMPS connectorC01 and ECM connector of this Study

3.Study Measure resistance between terminal 1 of the CMPS harness connectorC01 and chassis ground.

A.Study [Specification] Approx.0Ω

4.Is the resistance near the specified value of this Study?

YES

1)Go to "Signal Circuit Inspection" procedure Study.

NO

1)Repair open in harness, Go to "Verification of Vehicle Repair" procedure Study.

Signal Circuit Inspection

Check for Open in Harness

1.IG KEY : OFF , Engine : OFF

2.Disconnect CMPS connectorC01 and ECM connector Study.

3.This Study Measure resistance between terminal 2 of the CMPS harness connectorC01 and 18 of the ECM harness connectorC22-4.

A.Study [Specification] Approx.0Ω

4.Is the resistance near the specified value Study?

YES

1)Go to "Check for Short to Ground in Harness study"

NO

1)Repair open in harness, Go to "Verification of Vehicle Repair" procedure Study.

Check for Short to Ground in Harness

1.IG KEY : OFF , Engine : OFF

2.Disconnect CMPS connectorC01

3.Study Measure resistance between terminal 2 of the CMPS harness connectorC01 and chassis ground.

A.Study [Specification] infinite(∞Ω)

4.Does the resistance indicate open?

YES

1)Go to "Check for Short to Battery in Harness"

NO

1)Repair short to chassis ground in harness, Go to "Verification of Vehicle Repair" procedure.

Check for Short to Battery in Harness

1.IG KEY : OFF , Engine : OFF

2.Disconnect CMPS connectorC01.

3.IG KEY : ON , Engine : OFF

4.Study Measure voltage between terminal 2 of the CMPS harness connectorC01 and chassis ground.

A.Study [Specification] Approx.0V

5.Is the voltage near the specified value of this Study?

YES

1)Go to "Component Inspection" procedure Study.

NO

1)Repair short to battery in harness, Go to "Verification of Vehicle Repair" procedure Study.

More Info Study & Please Leave comments

more info:

1. Tech 1
2. Tech 2